Read our FAQ


The kdFi Cinch is a universal programmable Engine Management System for ignition and fuel injection on MSextra Base (MS2 V3.0) which is a full replacement for the original EFI System .

 

The fuel calculation options can be switched by the free Software Tunerstudio between ALPHA-N,speed density and hybrid as main variable for ignition and fuel tables.

 

So you can use the kdFi V1.4 on normal Gasoline Engine or supercharced ones.


Connector set included. 



Features:


  • full compatible to MSextra Software
  • build your own setup !only Fuel 1-4 outputs are populated on the cinch!
  • MS2 onboard / Firmware MS2extra
  • free Software / Open Source
  • Fuel Table 16x16
  • Ignition Table 12x12
  • USB Conector
  • Super accurate onboard wideband lambda controller 
  • Two Lambda inputs
  • supports 12 coils
  • supports low impedance injectors
  • supports 2 and 3 wire Fast Idle Valves
  • user programable Relais outputs
  • electronical boost control
  • Launch Control
  • Table switching
  • Tacho output
  • permanent Barometric correction prepared
  • Rev input via: VR-Sensor, Hallsensor
  • supports CAN Bus

KdFi Cinch Manual
USB Driver
KdFi Cinch Connection Diagram

Write a review

Please login or register to review

KDFI V1.4 Cinch enclosure

  • Product Code: Kdfi enclosure cinch
  • Availability: Out Of Stock
  • 395.00€

  • Ex Tax: 326.45€

Available Options


Related Products

KDFI V1.4 connector set

KDFI V1.4 connector set

Connector set to connect the wiring loom with the KDFI ECU ..

24.99€ Ex Tax: 20.65€

KDFI V1.4 Bluetooth Module Kperformance

KDFI V1.4 Bluetooth Module Kperformance

This Bluetooth Module works with all kdFi V1.4.Just plug it between KdFi V1.4 Module and the lower P..

65.34€ Ex Tax: 54.00€

Map Sensor MPX4250

Map Sensor MPX4250

Universal internal MAP sensor good  for 1.5bar of boost, or for NA usage in non-boosted applica..

32.55€ Ex Tax: 26.90€

Map Sensor MPX5700

Map Sensor MPX5700

Universal internal MAP sensor good for 6bar of boost, or for NA use in non-boosted applications...

32.55€ Ex Tax: 26.90€

Bulkhead Brass Pipe fitting

Bulkhead Brass Pipe fitting

Bulkhead fitting for pass throughs of fuel, water air etc Ideal as a transit for KdFi Ecu's int..

5.26€ Ex Tax: 4.35€

KDFI V1.4 WIFI Module Kperformance

KDFI V1.4 WIFI Module Kperformance

Word premiere plug&play WIFI module for the KdFi V1.4 This WIFI Module works with all kdFi ..

64.99€ Ex Tax: 53.71€

High Fun Map Sensor

High Fun Map Sensor

Good for 4bar of boost, or for NA use in non-boosted applications.This board uses the easy to solder..

33.76€ Ex Tax: 27.90€

Manifold Map Sensor 3bar

Manifold Map Sensor 3bar

Universal MAP sensor good for 2 bar of boost.Pinout:1/A = + 5 Vdc2/B = GND3/C =Signal OUTFeatures:Po..

41.99€ Ex Tax: 34.70€

External Map Sensor 3bar

External Map Sensor 3bar

Universal MAP sensor good for 2 bar of boost, used on Delta Integrale & Cosworth engines.Pinout:..

41.99€ Ex Tax: 34.70€